Note: The product has a version with a mounting bracket and a version without a mounting bracket. Please choose the product that suits you according to your actual situation. Please note that for product beauty, products with mounting brackets do not have the word 'Gear' on the top of the surface. Special Function: Touch Sensor Robust Design High Speed Warning Auto Brightness Control Flipping the display upside down No need to cut any wires and no need for soldering Even if you do not run the motorcycle, you can complete the product settings. The setting can be completed when the motorcycle is completely stopped. Sign Description: C: Code Reading the firmware version L: Learning Learning the gear positions F: Filtering Adjusting the filtering (sampling period) b: Brightness Adjusting the sensitivity of the light sensor H: HSW High Speed Warning function E: ESW Engine Speed Warning function Upside down Flipping the display upside down Defaults Resetting all values to factory defaults Features: Condition: Light Color: Red/Blue/Green 1-6 Level IP68 Waterproof Gear display The Fact: FAST AND ACCURATE Instant and accurate indication of the selected gear (right after the clutch is released) for added control and safety. The sampling period can be adjusted to make the response quicker or slower, depending on shift speed and signal conditions. TOUCH SENSOR All settings can be done via the touch sensor so theres no opening on the housing, it is completely sealed and encapsulated in epoxy. The touch sensitive area is on the TOP of the unit. However, after programming, the unit can be mounted even with the top side stuck to the dashboard (via the sticky pads supplied) and will function properly. It can also be used with the optional GFYSHIP Mount. AUTO BRIGHTNESS CONTROL The brightness of the display is adjusted automatically according to the ambient light intensity. The sensitivity of the sensor can be fine-tuned in the menu. HIGH SPEED WARNING FUNCTION If you wish, you may set the unit to warn you when the set road speed and/or the set engine speed is exceeded. ROBUST DESIGN - Full SMT-design, encapsulated in epoxy - Flash memory to store user settings even with the battery disconnected - Only inspected, high quality components are built in - Each unit is extensively tested prior to shipping Fitment: For Suzuki GSF650 Bandit 2007-2015 For Suzuki GSF1250 N Bandit 2007-2013 For Suzuki GSF1250 NA Bandit 2007-2013 For Suzuki GSF1250 S Bandit 2007-2016 For Suzuki GSF1250 SA Bandit 2007-2016 Installation: 1. Gain access to the Gear Position Sensor (GPS) connector. Normally this involves the following: - Remove the seat - Lift up or remove the fuel tank Look for a matching connector on the bike to your model. You may find more than one of this connector under the fuel tank. You need the one that (normally) has Pink, Blue and Black/White wires. 2. Disconnect the GPS coupler. Make sure the gearbox is in Neutral and turn the ignition switch ON. Wait a few seconds. The Neutral indicator should NOT be lit with disconnected GPS coupler. After confirming this, turn the ignition OFF and proceed to the next step. 3. Connect the GFYSHIP plugs to the GPS coupler. 4. Connect the GFYSHIP Red wire to an ignition switched +12V power lead by using the Red wire tap connector supplied. Usage: Place the unstripped bike wire (switched +12V) inside the run channel. Close the side cover until latched. Cut off the excess length, then insert the unstripped tap wire (GIpro Red) completely and check its position. Insert the blade (u-contact) and press down by finger pressure. Then, fully depress the u-contact with pliers. Close the hinged top cover until latched. The power must be ON even when the engine run switch is switched off. We recommend tapping the Orange/Green (orange with thin green stripe) wire at the 2-pole rear brake light switch connector or at the diagnostic connector. Set Up: Note: If the unit does not indicate the gears correctly with the pre-set gear position values, youll need to start the Learning procedure.The TOP side of the housing is the touch sensitive area so it must be kept free, away from all objects. If the unit is in a mount, remove it first. - Have the gearbox in Neutral. - Have the ignition OFF (the display must be blank). - Turn the ignition ON and the engine stop switch to RUN position (the display should count up and then show 0). Wait at least 2 seconds. - With your index finger (without gloves) tap the top side of the unit and hold your finger until the first menu sign shows up. Remove your finger now. Note: If the gearbox is switched to a gear then accessing the menu will be disabled even if you shift back to neutral. Cycle the ignition key to start overIf the unit does not indicate the gears correctly, start the Auto-Lea