설명
600W DC DC Boost Converter Step UP Converter Module Power Supply 12V - 60V DC-DC Step Up Booster Converter Constant Voltage
Features:
600W High power boost module
Input voltage :12-60V or 8-16V Selectable
Wide output voltage (12-80V) adjustable
Output current (0.1-12A) Adjustable
High efficiency
Ultra-low dropout voltage
Module parameters:
Module Properties: non-isolated step-up module (BOOST)
Input voltage: two input voltage ranges selectable (selectable with jumper on board)
1). 8-16V input ( In this input mode,please do not over-voltage input, otherwise it will burn module)
2). 12-60V input(default)
Input Current : 16A (MAX) Please enhance heat dissipation when current over than 10A
Static Current : 15mA (12V to 20V. The output voltage increase, the static current will increase a little)
Output voltage: 12-80V (continuously adjustable) ( the default output about 19V )
Output Current : 12A MAX, if over 10A please enhance heat dissipation ( the higher the dropout voltage, the smaller the current )
Constant current range :0.1-12A
Output power : = input voltage * 10A, such as: input 12V * 10A = 120W, input 24V * 10A = 240W, Input 36V * 10A = 360W, input 48V * 10A = 480W, input 60V * 10A = 600W. If you need more high-power, two modules can be used in parallel , for example if you need 15A output, then connect two modules in parallel ,the current of each module set to 8A then is OK.
Operating temperature: -40°C to +85°C ( if temperature too high , please enhance heat dissipation)
Operating Frequency : 150KHz
Conversion efficiency : up to 95% ( affected by input voltage, output volage, current and dropout voltage )
Operating Ripple: about 100mV
Load Regulation rate: about 0.2%
Voltage regulation rate: about 2%
Overcurrent protection : Yes ( input exceeds 17A, automatically reduces the output voltage , maybe have errors)
Short-circuit protection: Yes (input with 20A fuse) double circuit protection, more safe.
Input Reverse Polarity Protection: No , ( if necessary , input add one diode in series)
Output prevent backflow : Yes, no need to add prevent backflow diode for charging .
Installation: two 3mm screws
Wiring: terminals, no welding.
Size: 76mm(L) x 60mm(W) * 56mm(H, the height of the heatsink is included)
Net weight: 205 g
Applications:
DIY a regulated power supply, only 12V input, output 12-80V adjustable.
Power supply for your electronic device , according to your system can set the output voltage value .
As a vehicle power supply, power supply for your laptop/PDA etc.
DIY a laptop mobile power supply, with 12V high capacity lithium battery pack, travel no worry.
Solar panels regulator.
Charge for the battery.
Drive high-power LED.
-
Fruugo ID:
59256910-119978578
-
EAN:
469518780987
제품 안전 정보
아래에 설명된 이 제품과 관련된 제품 안전 정보를 참조하십시오.
以下の情報は、この製品を販売する独立したサードパーティ小売業者によって提供されています。
제품 안전 라벨
안전 경고:
Please note that the product is safe under normal use conditions. However, improper use may lead to hazards such as damage, injury or other safety risks. Please read and follow the instructions carefully.This product complies with EU safety standards. However, for your safety, if any abnormality (such as strange smell, overheating, loose parts, etc.) is found during use, please stop using it immediately.In accordance with the EU General Product Safety Regulation, we remind you that this product is only suitable for [specific applicable people / scenarios]. Use in non - specified people / scenarios may bring potential safety hazards.
