2N EasyGate IP+ 4G VoLTE/VOIP (EU/UK)

2N EasyGate IP+ 4G VoLTE/VoIP lift gateway (EU/UK) The 2N EasyGate IP+ is the extended version of the 2N EasyGate IP. It is an LTE/VoIP gateway for emergency communication between the lift car and the call centre, and it adds the interfaces needed to connect the lift controller directly: three Ethernet ports, RS232, RS485 and CAN bus. Remote diagnostics, monitoring and control work without any additional module. Analogue lift emergency phones (for example 2N Lift1) connect to the FXS port and are carried over 4G VoLTE or SIP. DTMF is transmitted over SIP, so lift identification stays reliable where mobile networks distort analogue tones. The gateway complies with current cybersecurity standards and can be managed remotely through 2N Elevator Center. EasyGate IP+ or EasyGate IP? The difference is on the back The standard 2N EasyGate IP (5023001E) has no Ethernet port: it carries the emergency call over the mobile network only and is configured over USB. The EasyGate IP+ (5025101E) adds three RJ-45 Ethernet ports plus RS485 and CAN bus for the lift controller and the building network. See the rear-view photo. InterfaceEasyGate IP (5023001E)EasyGate IP+ (5025101E)Ethernet RJ-45None3× (WAN/LAN1, LAN2, LAN3), 10/100/1000RS485 and CAN busNoneYes, screw terminalsmicroSD slotNoneYesRS232YesYesRelay output and inputYesYesFXS line for the lift phoneYesYesDual SIM, 4G VoLTE, battery backup, USB configYesYes Choose the IP+ when the gateway must connect to the lift controller over Ethernet, RS485 or CAN, or use a wired internet connection in the shaft. Choose the standard EasyGate IP for a mobile-only emergency line. Key features 2G / 3G / 4G VoLTE on all EU/UK networks. Install on today's network, switch to 4G later without changing hardware.Reliable DTMF through SIP-based VoIP for accurate lift car identification.VoIP without replacing cabin hardware. Existing analogue emergency phones connect to the FXS line.Controller interfaces built in: 3× Ethernet (1× WAN + 2× LAN, or 3× LAN), RS232, RS485, CAN.Relay output and short-circuit input for fault signalling to the controller.Dual SIM with automatic fallback to the second SIM on signal loss.Backup battery (4× AA NiMH) keeps emergency calls working during a power failure.Built for the shaft: IP43 casing, operation up to +85 °C without batteries.Fast setup with predefined configuration templates; web UI over USB or cloud via 2N Elevator Center. Technical specifications Power supply Mains adapter: 100–240 V / 12 V, 1 A (EU cable without plug)DC input: 9–30 V DCBackup: 4× AA NiMH 1.2 V, min. 2000 mAh, continuously monitoredConsumption at 12 V: 110 mA standby, 310 mA typical during a VoLTE/SIP call Cellular network (EU version, module EC25-E) LTE bands: B1 / B3 / B5 / B7 / B8 / B20 / B38 / B40 / B41UMTS bands: B1 / B5 / B8GSM/EDGE bands: B3 / B8SIM cards: 2 slots, 3 V and 1.8 VAntenna: SMA connector, 50 Ω (antenna included) VoIP Protocols: SIP (RFC 3261) over UDP, SIPs, SRTP, TLSDTMF: in-band, SIP INFO (RFC 2976), RTP Event (RFC 2833) Line interface (FXS) Type: 2-wire analogue FXSCall impedance: selectable 600 Ω / Zr EU / Zr AustraliaLoop voltage / current: 48 V DC, 15–40 mA, loop resistance up to 800 ΩRing voltage / frequency: adjustable 35–60 V RMS, 10–60 Hz Data and control interfaces Ethernet: 3× RJ-45, 10/100/1000BaseT, configurable as 3× LAN or 2× LAN + WANSerial: RS232, RS485, CANInput: 1× short-circuit input, voltage-freeRelay output: NO and NC contacts, max 30 V DC / 1 A or 125 V AC / 0.3 A Configuration Local: web UI via USBCloud: 2N Elevator Center Mechanical and environmental IP rating: IP43Operating temperature: –40 °C to +85 °C without batteries, 0 °C to +45 °C with batteriesStorage temperature: –20 °C to +45 °CHumidity: …